Synway ATP-24A/PCIe (2.0) - 8 ports

Synway ATP-24A/PCIe (2.0) - 8 ports

The Synway ATP Series ATP-24A/PCI, ATP-24A/PCI+, ATP-24A/PCIe, ATP-24A/PCIe+, ATP-24A/PCI(2.0), ATP-24A/PCI+(2.0), ATP-24A/PCIe(2.0), ATP-24A/PCIe+(2.0) are 24-channel analog tap passive boards with PCI or PCIe bus, used especially for recording of analog subscriber lines.

Functions

• High-impedance passive monitoring through parallel connection

• A variety of ways to start/stop recording

• Support of simultaneous recording on 24 channels

• Caller ID detection, FSK/DTMF support

• DTMF digits detection

• Simultaneous detection of DTMF and FSK

• Programmable tone analyzer detects all kinds of tones

• Activity/silence detection

• Automatic Gain Control (AGC) support in recording/playback operation

• Call progress monitoring

• Automatic detection of line voltage

• Automatically checks board to see if recording modules are correctly inserted

• ATP-24A/PCI+, ATP-24A/PCIe+, ATP-24A/PCI+(2.0) and ATP-24A/PCIe+(2.0) boards support hardware-based MS-GSM, G.729A and MP3 formats for encoding

Dimensions

ATP-24A/PCI, ATP-24A/PCI+, ATP-24A/PCIe, ATP-24A/PCIe+:
310×115 mm2 (excluding L-bracket)
ATP-24A/PCI(2.0), ATP-24A/PCI+(2.0), ATP-24A/PCIe(2.0), ATP-24A/PCIe+(2.0):
160×111mm2 (excluding L-bracket)

Weight

ATP-24A/PCI, ATP-24A/PCI+:
≈250g (including 2 8-channel modules)
ATP-24A/PCIe, ATP-24A/PCIe+:
≈200g (including 2 8-channel modules)
ATP-24A/PCI(2.0), ATP-24A/PCI+(2.0), ATP-24A/PCIe(2.0), ATP-24A/PCIe+(2.0):
≈215g (including 2 8-channel modules)

Environment
Operating temperature: 0℃—55℃
Storage temperature: -20℃—85℃
Humidity: 8%— 90% non-condensing
Storage humidity: 8%— 90% non-condensing
Input/output Interface
Headset jack: One φ3.5 stereo jack
Telephone line jack: A 50-pin RJ21 connector

Audio Specifications
Codec: CCITT A/μ-Law 64kbps
IMA ADPCM 32kbps
Output power: ≥50mW
Distortion: ≤2%
Frequency response: 300-3400Hz(±3dB)
Signal-to-noise ratio: ≥38dB
Echo suppression: ≥40dB
Maximum System Capacity
Up to 10 boards concurrently per system; up to 24 channels per board

Power Requirements
ATP-24A/PCI, ATP-24A/PCI+, ATP-24A/PCIe, ATP-24A/PCIe+:
+3.3V DC, 700mA

+5V DC, 200mA (PCI board only)
-12V DC, 120mA (PCI board only)
+12V DC, 100mA
Maximum power consumption: ≤12W (PC power supply only)
ATP-24A/PCI(2.0), ATP-24A/PCI+(2.0):
+3.3V DC: 900mA
+5V DC: 200mA
+12V DC: 100mA
Maximum power consumption: ≤8W (PC power supply only)
ATP-24A/PCIe(2.0), ATP-24A/PCIe+(2.0):
+3.3VDC: 900mA
+12V DC: 300mA
Maximum power consumption: ≤9W (PC power supply only)

Impedance
Input impedance: ≥1MΩ/500V DC;
≥10kΩ/1000V AC
Insulation resistance for PC isolation from telephone line: ≥2MΩ/500V DC
Telephone line impedance: Compliant with the national standard impedance for three-component network

Audio Encoding & Decoding
16Bit PCM 128kbps
8Bit PCM 64kbps
A-Law 64kbps
μ-Law 64kbps
VOX 32kbps
ADPCM 32kbps
GSM 13.6kbps
MP3 8kbps
G.729A 8kbps
Sampling Rate
8kHz